diff options
Diffstat (limited to 'include/configs/db-88f6281-bp.h')
| -rw-r--r-- | include/configs/db-88f6281-bp.h | 96 |
1 files changed, 96 insertions, 0 deletions
diff --git a/include/configs/db-88f6281-bp.h b/include/configs/db-88f6281-bp.h new file mode 100644 index 0000000..1b5541e --- /dev/null +++ b/include/configs/db-88f6281-bp.h @@ -0,0 +1,96 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef _CONFIG_DB_88F6281_BP_H +#define _CONFIG_DB_88F6281_BP_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ +#define CONFIG_KW88F6281 1 /* SOC Name */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ +#define CONFIG_SYS_TCLK 166666667 +#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg +#define CONFIG_BUILD_TARGET "u-boot.kwb" + +/* additions for new ARM relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 + +#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ +#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */ +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ +#define CONFIG_KIRKWOOD_GPIO 1 + +/* + * NS16550 Configuration + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK +#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +/* + * Serial Port configuration + * The following definitions let you select what serial you want to use + * for your console driver. + */ + +#define CONFIG_CONS_INDEX 1 /* Console on UART0 */ + +/* + * Environment variables configurations + */ +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */ +#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE +#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */ +#define CONFIG_ENV_SIZE 0x01000 +#define CONFIG_ENV_OFFSET 0xC0000 + +/* + * U-Boot bootcode configuration + */ + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ + +/* size in bytes reserved for initial data */ + +#include <asm/arch/config.h> +/* There is no PHY directly connected so don't ask it for link status */ +#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN + +/* + * Other required minimal configurations + */ +#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ +#define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */ +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ + +/* + * SDIO/MMC Card Configuration + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MVEBU_MMC +#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE +#endif /* CONFIG_CMD_MMC */ + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ + +#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */ + +#endif /* _CONFIG_DB_88F6281_BP_H */ |