diff options
Diffstat (limited to 'include/configs/ge_bx50v3.h')
| -rw-r--r-- | include/configs/ge_bx50v3.h | 237 |
1 files changed, 237 insertions, 0 deletions
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h new file mode 100644 index 0000000..6de5119 --- /dev/null +++ b/include/configs/ge_bx50v3.h @@ -0,0 +1,237 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2015 Timesys Corporation + * Copyright (C) 2015 General Electric Company + * Copyright (C) 2014 Advantech + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * + * Configuration settings for the GE MX6Q Bx50v3 boards. + */ + +#ifndef __GE_BX50V3_CONFIG_H +#define __GE_BX50V3_CONFIG_H + +#include <asm/arch/imx-regs.h> +#include <asm/mach-imx/gpio.h> + +#define CONFIG_BOARD_NAME "General Electric Bx50v3" + +#define CONFIG_MXC_UART_BASE UART3_BASE +#define CONSOLE_DEV "ttymxc2" + +#include "mx6_common.h" +#include <linux/sizes.h> + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) + +#define CONFIG_MXC_UART + +/* SATA Configs */ +#ifdef CONFIG_CMD_SATA +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_DWC_AHSATA_PORT_ID 0 +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR +#define CONFIG_LBA48 +#endif + +/* USB Configs */ +#ifdef CONFIG_USB +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 + +#define CONFIG_USBD_HS +#define CONFIG_USB_GADGET_MASS_STORAGE +#endif + +/* Networking Configs */ +#ifdef CONFIG_NET +#define CONFIG_FEC_MXC +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 4 +#define CONFIG_PHY_ATHEROS +#endif + +/* Serial Flash */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_LOADADDR 0x12000000 + +#ifdef CONFIG_NFS_CMD +#define NETWORKBOOT \ + "setnetworkboot=" \ + "setenv ipaddr 172.16.2.10; setenv serverip 172.16.2.20; " \ + "setenv gatewayip 172.16.2.20; setenv nfsserver 172.16.2.20; " \ + "setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \ + "setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \ + "setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \ + "setenv bootargs $bootargs cma=128M bootcause=POR console=${console} ${videoargs} " \ + "setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \ + "setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \ + "networkboot=" \ + "run setnetworkboot; " \ + "nfs ${loadaddr} /srv/nfs/fitImage; " \ + "bootm ${loadaddr}#conf@${confidx}\0" \ + +#define CONFIG_NETWORKBOOTCOMMAND \ + "run networkboot; " \ + +#else +#define NETWORKBOOT \ + +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + NETWORKBOOT \ + "bootcause=POR\0" \ + "image=/boot/fitImage\0" \ + "fdt_high=0xffffffff\0" \ + "dev=mmc\0" \ + "devnum=2\0" \ + "rootdev=mmcblk0p\0" \ + "quiet=quiet loglevel=0\0" \ + "console=" CONSOLE_DEV "\0" \ + "setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \ + "ro rootwait cma=128M " \ + "bootcause=${bootcause} " \ + "${quiet} console=${console} ${rtc_status} " \ + "${videoargs}" "\0" \ + "doquiet=" \ + "if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \ + "then setenv quiet; fi\0" \ + "hasfirstboot=" \ + "ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \ + "/boot/bootcause/firstboot\0" \ + "swappartitions=" \ + "setexpr partnum 3 - ${partnum}\0" \ + "failbootcmd=" \ + "bx50_backlight_enable; " \ + "msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \ + "echo $msg; " \ + "setenv stdout vga; " \ + "echo \"\n\n\n\n \" $msg; " \ + "setenv stdout serial; " \ + "mw.b 0x7000A000 0xbc; " \ + "mw.b 0x7000A001 0x00; " \ + "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \ + "altbootcmd=" \ + "run doquiet; " \ + "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \ + "run hasfirstboot || setenv partnum 0; " \ + "if test ${partnum} != 0; then " \ + "setenv bootcause REVERT; " \ + "run swappartitions loadimage doboot; " \ + "fi; " \ + "run failbootcmd\0" \ + "loadimage=" \ + "ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \ + "doboot=" \ + "echo Booting from ${dev}:${devnum}:${partnum} ...; " \ + "run setargs; " \ + "bootm ${loadaddr}#conf@${confidx}\0" \ + "tryboot=" \ + "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \ + "run loadimage || run swappartitions && run loadimage || " \ + "setenv partnum 0 && echo MISSING IMAGE;" \ + "run doboot; " \ + "run failbootcmd\0" \ + +#define CONFIG_MMCBOOTCOMMAND \ + "if mmc dev ${devnum}; then " \ + "run doquiet; " \ + "run tryboot; " \ + "fi; " \ + +#define CONFIG_USBBOOTCOMMAND \ + "echo Unsupported; " \ + +#ifdef CONFIG_NFS_CMD +#define CONFIG_BOOTCOMMAND CONFIG_NETWORKBOOTCOMMAND +#elif CONFIG_CMD_USB +#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND +#else +#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND +#endif + + +/* Miscellaneous configurable options */ + +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x10010000 +#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +/* Physical Memory Map */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* environment organization */ +#define CONFIG_ENV_SIZE (8 * 1024) +#define CONFIG_ENV_OFFSET (768 * 1024) +#define CONFIG_ENV_SECT_SIZE (64 * 1024) + +#define CONFIG_SYS_FSL_USDHC_NUM 3 + +/* Framebuffer */ +#define CONFIG_HIDE_LOGO_VERSION +#define CONFIG_IMX_HDMI +#define CONFIG_IMX_VIDEO_SKIP +#define CONFIG_CMD_BMP + +#define CONFIG_IMX6_PWM_PER_CLK 66000000 + +#define CONFIG_PCI +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_PCIE_IMX +#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) +#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5) + +#define CONFIG_RTC_RX8010SJ +#define CONFIG_SYS_RTC_BUS_NUM 2 +#define CONFIG_SYS_I2C_RTC_ADDR 0x32 + +/* I2C Configs */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_MXC_I2C1 +#define CONFIG_SYS_I2C_MXC_I2C2 +#define CONFIG_SYS_I2C_MXC_I2C3 + +#define CONFIG_SYS_NUM_I2C_BUSES 11 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {1, {I2C_NULL_HOP} }, \ + {2, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \ + } + +#define CONFIG_BCH + +#endif /* __GE_BX50V3_CONFIG_H */ |