diff options
Diffstat (limited to 'include/configs/ids8313.h')
| -rw-r--r-- | include/configs/ids8313.h | 306 |
1 files changed, 306 insertions, 0 deletions
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h new file mode 100644 index 0000000..43cb14c --- /dev/null +++ b/include/configs/ids8313.h @@ -0,0 +1,306 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2013 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * Based on: + * Copyright (c) 2011 IDS GmbH, Germany + * Sergej Stepanov <ste@ids.de> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_FSL_ELBC + +#define CONFIG_BOOT_RETRY_TIME 900 +#define CONFIG_BOOT_RETRY_MIN 30 +#define CONFIG_RESET_TO_RETRY + +#define CONFIG_SYS_SICRH 0x00000000 +#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D) + +#define CONFIG_HWCONFIG + +/* + * Definitions for initial stack pointer and data area (in DCACHE ) + */ +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ + - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Internal Definitions + */ +/* + * DDR Setup + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 + +/* + * Manually set up DDR parameters, + * as this board has not the SPD connected to I2C. + */ +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\ + 0x00010000 |\ + CSCONFIG_ROW_BIT_13 |\ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \ + CSCONFIG_BANK_BIT_3) + +#define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */ +#define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\ + (3 << TIMING_CFG0_WRT_SHIFT) |\ + (3 << TIMING_CFG0_RRT_SHIFT) |\ + (3 << TIMING_CFG0_WWT_SHIFT) |\ + (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_MRS_CYC_SHIFT)) +#define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\ + (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\ + (4 << TIMING_CFG1_ACTTORW_SHIFT) |\ + (7 << TIMING_CFG1_CASLAT_SHIFT) |\ + (4 << TIMING_CFG1_REFREC_SHIFT) |\ + (4 << TIMING_CFG1_WRREC_SHIFT) |\ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\ + (2 << TIMING_CFG1_WRTORD_SHIFT)) +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\ + (5 << TIMING_CFG2_CPO_SHIFT) |\ + (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\ + (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\ + (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\ + (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) + +#define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\ + (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + +#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\ + SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\ + SDRAM_CFG_DBW_32 |\ + SDRAM_CFG_SDRAM_TYPE_DDR2) + +#define CONFIG_SYS_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\ + (0x0242 << SDRAM_MODE_SD_SHIFT)) +#define CONFIG_SYS_DDR_MODE_2 0x00000000 +#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\ + DDRCDR_PZ_NOMZ |\ + DDRCDR_NZ_NOMZ |\ + DDRCDR_ODT |\ + DDRCDR_M_ODR |\ + DDRCDR_Q_DRN) + +/* + * on-board devices + */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC2 + +/* + * NOR FLASH setup + */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT +#define CONFIG_FLASH_SHOW_PROGRESS 50 + +#define CONFIG_SYS_FLASH_BASE 0xFF800000 +#define CONFIG_SYS_FLASH_SIZE 8 + + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 128 + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 + +/* + * NAND FLASH setup + */ +#define CONFIG_SYS_NAND_BASE 0xE1000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 1 +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_PAGE_SIZE (2048) +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) +#define NAND_CACHE_PAGES 64 + + +/* + * MRAM setup + */ +#define CONFIG_SYS_MRAM_BASE 0xE2000000 +#define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */ + +#define CONFIG_SYS_OR_TIMING_MRAM + + +/* + * CPLD setup + */ +#define CONFIG_SYS_CPLD_BASE 0xE3000000 +#define CONFIG_SYS_CPLD_SIZE 0x8000 + +#define CONFIG_SYS_OR_TIMING_MRAM + + +/* + * HW-Watchdog + */ +#define CONFIG_WATCHDOG 1 +#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF + +/* + * I2C setup + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_RTC_PCF8563 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 + +/* + * Ethernet setup + */ +#ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define TSEC1_PHY_ADDR 0x1 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC1_PHYIDX 0 +#endif + +#ifdef CONFIG_TSEC2 +#define CONFIG_HAS_ETH1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define TSEC2_PHY_ADDR 0x3 +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC2_PHYIDX 0 +#endif +#define CONFIG_ETHPRIME "TSEC1" + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) + +#define CONFIG_HAS_FSL_DR_USB +#define CONFIG_SYS_SCCR_USBDRCM 3 + +/* + * U-Boot environment setup + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024) + +/* + * Environment Configuration + */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ + + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_NETDEV eth1 +#define CONFIG_HOSTNAME "ids8313" +#define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx" +#define CONFIG_BOOTFILE "ids8313/uImage" +#define CONFIG_UBOOTPATH "ids8313/u-boot.bin" +#define CONFIG_FDTFILE "ids8313/ids8313.dtb" +#define CONFIG_LOADADDR 0x400000 +#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo" + +/* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_CBSIZE 1024 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x00001000 +#define CONFIG_SYS_MEMTEST_END 0x00C00000 + +#define CONFIG_SYS_LOAD_ADDR 0x100000 +#define CONFIG_LOADS_ECHO +#define CONFIG_TIMESTAMP +#define CONFIG_BOOTCOMMAND "run boot_cramfs" +#undef CONFIG_SYS_LOADS_BAUD_CHANGE + +#define CONFIG_JFFS2_NAND +#define CONFIG_JFFS2_DEV "0" + +/* mtdparts command line support */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" __stringify(CONFIG_NETDEV) "\0" \ + "ethprime=TSEC1\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot ${loadaddr} ${uboot}; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +${filesize}; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +${filesize}; " \ + "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ + " ${filesize}; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +${filesize}; " \ + "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ + " ${filesize}\0" \ + "console=ttyS0\0" \ + "fdtaddr=0x780000\0" \ + "kernel_addr=ff800000\0" \ + "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \ + "setbootargs=setenv bootargs " \ + "root=${rootdev} rw console=${console}," \ + "${baudrate} ${othbootargs}\0" \ + "setipargs=setenv bootargs root=${rootdev} rw " \ + "nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:off " \ + "console=${console},${baudrate} ${othbootargs}\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ + "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ + "\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv rootdev /dev/nfs;" \ + "run setipargs;run addmtd;" \ + "tftp ${loadaddr} ${bootfile};" \ + "tftp ${fdtaddr} ${fdtfile};" \ + "fdt addr ${fdtaddr};" \ + "bootm ${loadaddr} - ${fdtaddr}" + +/* UBI Support */ + +#endif /* __CONFIG_H */ |