summaryrefslogtreecommitdiff
path: root/include/configs/integrator-common.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/integrator-common.h')
-rw-r--r--include/configs/integrator-common.h90
1 files changed, 90 insertions, 0 deletions
diff --git a/include/configs/integrator-common.h b/include/configs/integrator-common.h
new file mode 100644
index 0000000..9223fc2
--- /dev/null
+++ b/include/configs/integrator-common.h
@@ -0,0 +1,90 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2012
+ * Linaro
+ * Linus Walleij <linus.walleij@linaro.org>
+ * Common ARM Integrator configuration settings
+ */
+
+#define CONFIG_SYS_MEMTEST_START 0x100000
+#define CONFIG_SYS_MEMTEST_END 0x10000000
+#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */
+#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+
+/*
+ * There are various dependencies on the core module (CM) fitted
+ * Users should refer to their CM user guide
+ */
+#include "armcoremodule.h"
+
+/*
+ * Initialize and remap the core module, use SPD to detect memory size
+ * If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
+ * the core module has a CM_INIT register
+ * then the U-Boot initialisation code will
+ * e.g. ARM Boot Monitor or pre-loader is repeated once
+ * (to re-initialise any existing CM_INIT settings to safe values).
+ *
+ * This is usually not the desired behaviour since the platform
+ * will either reboot into the ARM monitor (or pre-loader)
+ * or continuously cycle thru it without U-Boot running,
+ * depending upon the setting of Integrator/CP switch S2-4.
+ *
+ * However it may be needed if Integrator/CP switch S2-1
+ * is set OFF to boot direct into U-Boot.
+ * In that case comment out the line below.
+ */
+#define CONFIG_CM_INIT
+#define CONFIG_CM_REMAP
+#define CONFIG_CM_SPD_DETECT
+
+/*
+ * The ARM boot monitor initializes the board.
+ * However, the default U-Boot code also performs the initialization.
+ * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT
+ * - see documentation supplied with board for details of how to choose the
+ * image to run at reset/power up
+ * e.g. whether the ARM Boot Monitor runs before U-Boot
+ */
+/* #define CONFIG_SKIP_LOWLEVEL_INIT */
+
+/*
+ * The ARM boot monitor does not relocate U-Boot.
+ * However, the default U-Boot code performs the relocation check,
+ * and may relocate the code if the memory map is changed.
+ * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT
+ */
+/* #define SKIP_CONFIG_RELOCATE_UBOOT */
+
+/*
+ * Physical Memory Map
+ */
+#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * FLASH and environment organization
+ * Top varies according to amount fitted
+ * Reserve top 4 blocks of flash
+ * - ARM Boot Monitor
+ * - Unused
+ * - SIB block
+ * - U-Boot environment
+ */
+#define CONFIG_SYS_FLASH_BASE 0x24000000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+/* Timeout values in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Erase Timeout */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Write Timeout */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */