diff options
Diffstat (limited to 'include/configs/lx2160ardb.h')
| -rw-r--r-- | include/configs/lx2160ardb.h | 110 |
1 files changed, 110 insertions, 0 deletions
diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h new file mode 100644 index 0000000..c6bacb6 --- /dev/null +++ b/include/configs/lx2160ardb.h @@ -0,0 +1,110 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#ifndef __LX2_RDB_H +#define __LX2_RDB_H + +#include "lx2160a_common.h" + +/* Qixis */ +#define QIXIS_XMAP_MASK 0x07 +#define QIXIS_XMAP_SHIFT 5 +#define QIXIS_RST_CTL_RESET_EN 0x30 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x20 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_QSPI 0xff +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SD +#define QIXIS_RCW_SRC_SD 0x08 +#define NON_EXTENDED_DUTCFG + +/* VID */ + +#define I2C_MUX_CH_VOL_MONITOR 0xA +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x63 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 +#define CONFIG_VID_FLS_ENV "lx2160ardb_vdd_mv" +#define CONFIG_VID + +/* The lowest and highest voltage allowed*/ +#define VDD_MV_MIN 775 +#define VDD_MV_MAX 855 + +/* PM Bus commands code for LTC3882*/ +#define PMBUS_CMD_PAGE 0x0 +#define PMBUS_CMD_READ_VOUT 0x8B +#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 +#define PMBUS_CMD_VOUT_COMMAND 0x21 +#define PWM_CHANNEL0 0x0 + +#define CONFIG_VOL_MONITOR_LTC3882_SET +#define CONFIG_VOL_MONITOR_LTC3882_READ + +/* RTC */ +#define CONFIG_SYS_RTC_BUS_NUM 4 + +/* MAC/PHY configuration */ +#if defined(CONFIG_FSL_MC_ENET) +#define CONFIG_MII +#define CONFIG_ETHPRIME "DPMAC1@xgmii" + +#define AQR107_PHY_ADDR1 0x04 +#define AQR107_PHY_ADDR2 0x05 +#define AQR107_IRQ_MASK 0x0C + +#define CORTINA_NO_FW_UPLOAD +#define CORTINA_PHY_ADDR1 0x0 +#define INPHI_PHY_ADDR1 0x0 + +#define RGMII_PHY_ADDR1 0x01 +#define RGMII_PHY_ADDR2 0x02 + +#endif + +/* EMC2305 */ +#define I2C_MUX_CH_EMC2305 0x09 +#define I2C_EMC2305_ADDR 0x4D +#define I2C_EMC2305_CMD 0x40 +#define I2C_EMC2305_PWM 0x80 + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXTRA_ENV_SETTINGS \ + "lx2160ardb_vdd_mv=800\0" \ + "BOARD=lx2160ardb\0" \ + "xspi_bootcmd=echo Trying load from flexspi..;" \ + "sf probe 0:0 && sf read $load_addr " \ + "$kernel_start $kernel_size ; env exists secureboot &&" \ + "sf read $kernelheader_addr_r $kernelheader_start " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + " bootm $load_addr#$BOARD\0" \ + "sd_bootcmd=echo Trying load from sd card..;" \ + "mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd ;" \ + "env exists secureboot && mmc read $kernelheader_addr_r "\ + "$kernelhdr_addr_sd $kernelhdr_size_sd " \ + " && esbc_validate ${kernelheader_addr_r};" \ + "bootm $load_addr#$BOARD\0" + +#include <asm/fsl_secure_boot.h> + +#endif /* __LX2_RDB_H */ |