diff options
Diffstat (limited to 'include/configs/omapl138_lcdk.h')
| -rw-r--r-- | include/configs/omapl138_lcdk.h | 240 |
1 files changed, 240 insertions, 0 deletions
diff --git a/include/configs/omapl138_lcdk.h b/include/configs/omapl138_lcdk.h new file mode 100644 index 0000000..1c41e7e --- /dev/null +++ b/include/configs/omapl138_lcdk.h @@ -0,0 +1,240 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Board + */ + +/* + * SoC Configuration + */ +#define CONFIG_MACH_OMAPL138_LCDK +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ +#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */ +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ + +#define CONFIG_SPL_BSS_START_ADDR DAVINCI_DDR_EMIF_DATA_BASE +#define CONFIG_SPL_BSS_MAX_SIZE 0x1080000 + +/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) + +/* memtest will be run on 16MB */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024) + +#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ + DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ + DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ + DAVINCI_SYSCFG_SUSPSRC_UART2 | \ + DAVINCI_SYSCFG_SUSPSRC_EMAC | \ + DAVINCI_SYSCFG_SUSPSRC_I2C) + +/* + * PLL configuration + */ + +/* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */ +#define CONFIG_SYS_DA850_PLL0_PLLM 18 +#define CONFIG_SYS_DA850_PLL1_PLLM 21 + +/* + * DDR2 memory configuration + */ +#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ + DV_DDR_PHY_EXT_STRBEN | \ + (0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDBCR ( \ + (1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \ + (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ + (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ + (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ + (4 << DV_DDR_SDCR_CL_SHIFT) | \ + (3 << DV_DDR_SDCR_IBANK_SHIFT) | \ + (2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) + +/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ +#define CONFIG_SYS_DA850_DDR2_SDBCR2 0 + +#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ + (19 << DV_DDR_SDTMR1_RFC_SHIFT) | \ + (1 << DV_DDR_SDTMR1_RP_SHIFT) | \ + (1 << DV_DDR_SDTMR1_RCD_SHIFT) | \ + (2 << DV_DDR_SDTMR1_WR_SHIFT) | \ + (6 << DV_DDR_SDTMR1_RAS_SHIFT) | \ + (8 << DV_DDR_SDTMR1_RC_SHIFT) | \ + (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ + (1 << DV_DDR_SDTMR1_WTR_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ + (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ + (2 << DV_DDR_SDTMR2_XP_SHIFT) | \ + (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ + (20 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ + (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ + (1 << DV_DDR_SDTMR2_RTP_SHIFT) | \ + (2 << DV_DDR_SDTMR2_CKE_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000492 +#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) + +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) + +/* + * I2C Configuration + */ +#define CONFIG_SYS_DAVINCI_I2C_SPEED 25000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ +#define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20 + +/* + * Flash & Environment + */ +#ifdef CONFIG_NAND +#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +#define CONFIG_ENV_SIZE (128 << 9) +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_PAGE_2K +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_SYS_NAND_MASK_CLE 0x10 +#define CONFIG_SYS_NAND_MASK_ALE 0x8 +#undef CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST +#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K +#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ + CONFIG_SYS_NAND_U_BOOT_SIZE - \ + CONFIG_SYS_MALLOC_LEN - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_NAND_ECCPOS { \ + 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, \ + 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \ + 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \ + 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 } +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 10 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_NAND_LOAD +#endif + +/* + * Network & Ethernet Configuration + */ +#ifdef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_DRIVER_TI_EMAC_USE_RMII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#endif + +/* + * U-Boot general configuration + */ +#define CONFIG_BOOTFILE "zImage" /* Boot file name */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) + +/* + * USB Configs + */ +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_REVISION_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTCOMMAND \ + "run envboot; " \ + "run mmcboot; " + +#define DEFAULT_LINUX_BOOT_ENV \ + "loadaddr=0xc0700000\0" \ + "fdtaddr=0xc0600000\0" \ + "scriptaddr=0xc0600000\0" + +#include <environment/ti/mmc.h> + +#define CONFIG_EXTRA_ENV_SETTINGS \ + DEFAULT_LINUX_BOOT_ENV \ + DEFAULT_MMC_TI_ARGS \ + "bootpart=0:2\0" \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "fdtfile=da850-lcdk.dtb\0" \ + "boot_fdt=yes\0" \ + "boot_fit=0\0" \ + "console=ttyS2,115200n8\0" + +#ifdef CONFIG_CMD_BDI +#define CONFIG_CLOCKS +#endif + +/* SD/MMC */ + +#ifdef CONFIG_ENV_IS_IN_MMC +#undef CONFIG_ENV_SIZE +#undef CONFIG_ENV_OFFSET +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ +#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */ +#endif + +/* defines for SPL */ +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ + CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN +#define CONFIG_SPL_STACK 0x8001ff00 +#define CONFIG_SPL_MAX_FOOTPRINT 32768 +#define CONFIG_SPL_PAD_TO 32768 + +/* additions for new relocation code, must added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ + GENERATED_GBL_DATA_SIZE) + +#include <asm/arch/hardware.h> + +#endif /* __CONFIG_H */ |