diff options
Diffstat (limited to 'include/configs/snapper9260.h')
| -rw-r--r-- | include/configs/snapper9260.h | 120 |
1 files changed, 120 insertions, 0 deletions
diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h new file mode 100644 index 0000000..b0408a5 --- /dev/null +++ b/include/configs/snapper9260.h @@ -0,0 +1,120 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Bluewater Systems Snapper 9260 and 9G20 modules + * + * (C) Copyright 2011 Bluewater Systems + * Author: Andre Renaud <andre@bluewatersys.com> + * Author: Ryan Mallon <ryan@bluewatersys.com> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* SoC type is defined in boards.cfg */ +#include <asm/hardware.h> +#include <linux/sizes.h> + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 + +/* CPU */ + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* SDRAM */ +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */ +#define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) + +/* Mem test settings */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024)) + +/* NAND Flash */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */ +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_RESET_PHY_R +#define CONFIG_AT91_WANTS_COMMON_PHY +#define CONFIG_TFTP_PORT +#define CONFIG_TFTP_TSIZE + +/* USB */ +#define CONFIG_USB_ATMEL +#define CONFIG_USB_ATMEL_CLK_SEL_PLLB +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 + +/* GPIOs and IO expander */ +#define CONFIG_ATMEL_LEGACY +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR 0x28 +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} } + +/* UARTs/Serial console */ +#define CONFIG_ATMEL_USART +#ifndef CONFIG_DM_SERIAL +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#endif + +/* I2C - Bit-bashed */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F +#define CONFIG_SOFT_I2C_READ_REPEATED_START +#define I2C_INIT do { \ + at91_set_gpio_output(AT91_PIN_PA23, 1); \ + at91_set_gpio_output(AT91_PIN_PA24, 1); \ + at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \ + at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \ + } while (0) +#define I2C_SOFT_DECLARATIONS +#define I2C_ACTIVE +#define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1); +#define I2C_READ at91_get_gpio_value(AT91_PIN_PA23); +#define I2C_SDA(bit) do { \ + if (bit) { \ + at91_set_gpio_input(AT91_PIN_PA23, 1); \ + } else { \ + at91_set_gpio_output(AT91_PIN_PA23, 1); \ + at91_set_gpio_value(AT91_PIN_PA23, bit); \ + } \ + } while (0) +#define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit) +#define I2C_DELAY udelay(2) + +/* Boot options */ +#define CONFIG_SYS_LOAD_ADDR 0x23000000 + +#define CONFIG_BOOTP_BOOTFILESIZE + +/* Environment settings */ +#define CONFIG_ENV_OVERWRITE + +/* Console settings */ + +/* U-Boot memory settings */ +#define CONFIG_SYS_MALLOC_LEN (1 << 20) + +#endif /* __CONFIG_H */ |