diff options
Diffstat (limited to 'include/configs/vf610twr.h')
| -rw-r--r-- | include/configs/vf610twr.h | 203 |
1 files changed, 203 insertions, 0 deletions
diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h new file mode 100644 index 0000000..ba85bc9 --- /dev/null +++ b/include/configs/vf610twr.h @@ -0,0 +1,203 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Configuration settings for the Freescale Vybrid vf610twr board. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/imx-regs.h> + +#define CONFIG_SYS_FSL_CLK + +#define CONFIG_MACH_TYPE 4146 + +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* Enable passing of ATAGs */ +#define CONFIG_CMDLINE_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) + +/* Allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* NAND support */ +#define CONFIG_SYS_NAND_ONFI_DETECTION + +#ifdef CONFIG_CMD_NAND +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR + +/* Dynamic MTD partition support */ +#endif + +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_SYS_FSL_ESDHC_NUM 1 + +#define CONFIG_FEC_MXC +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RMII +#define CONFIG_FEC_MXC_PHYADDR 0 + +/* QSPI Configs*/ + +#ifdef CONFIG_FSL_QSPI +#define FSL_QSPI_FLASH_SIZE (1 << 24) +#define FSL_QSPI_FLASH_NUM 2 +#define CONFIG_SYS_FSL_QSPI_LE +#endif + +/* I2C Configs */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ +#define CONFIG_SYS_SPD_BUS_NUM 0 + + +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +/* We boot from the gfxRAM area of the OCRAM. */ +#define CONFIG_BOARD_SIZE_LIMIT 520192 + +/* + * We do have 128MB of memory on the Vybrid Tower board. Leave the last + * 16MB alone to avoid conflicts with Cortex-M4 firmwares running from + * DDR3. Hence, limit the memory range for image processing to 112MB + * using bootm_size. All of the following must be within this range. + * We have the default load at 32MB into DDR (for the kernel), FDT at + * 64MB and the ramdisk 512KB above that (allowing for hopefully never + * seen large trees). This allows a reasonable split between ramdisk + * and kernel size, where the ram disk can be a bit larger. + */ +#define MEM_LAYOUT_ENV_SETTINGS \ + "bootm_size=0x07000000\0" \ + "loadaddr=0x82000000\0" \ + "kernel_addr_r=0x82000000\0" \ + "fdt_addr=0x84000000\0" \ + "fdt_addr_r=0x84000000\0" \ + "rdaddr=0x84080000\0" \ + "ramdisk_addr_r=0x84080000\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + MEM_LAYOUT_ENV_SETTINGS \ + "script=boot.scr\0" \ + "image=zImage\0" \ + "console=ttyLP1\0" \ + "fdt_file=vf610-twr.dtb\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ + "mmcpart=1\0" \ + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ + "update_sd_firmware_filename=u-boot.imx\0" \ + "update_sd_firmware=" \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "if mmc dev ${mmcdev}; then " \ + "if ${get_cmd} ${update_sd_firmware_filename}; then " \ + "setexpr fw_sz ${filesize} / 0x200; " \ + "setexpr fw_sz ${fw_sz} + 1; " \ + "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ + "fi; " \ + "fi\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ + +#define CONFIG_SYS_MEMTEST_START 0x80010000 +#define CONFIG_SYS_MEMTEST_END 0x87C00000 + +/* Physical memory map */ +#define PHYS_SDRAM (0x80000000) +#define PHYS_SDRAM_SIZE (128 * 1024 * 1024) + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_SIZE (8 * 1024) + +#define CONFIG_ENV_OFFSET (12 * 64 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 +#endif + +#ifdef CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE (64 * 2048) +#define CONFIG_ENV_SECT_SIZE (64 * 2048) +#define CONFIG_ENV_RANGE (512 * 1024) +#define CONFIG_ENV_OFFSET 0x180000 +#endif + +#endif |