diff options
Diffstat (limited to 'include/configs/vme8349.h')
| -rw-r--r-- | include/configs/vme8349.h | 333 |
1 files changed, 333 insertions, 0 deletions
diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h new file mode 100644 index 0000000..a4f2af4 --- /dev/null +++ b/include/configs/vme8349.h @@ -0,0 +1,333 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * esd vme8349 U-Boot configuration file + * Copyright (c) 2008, 2009 esd gmbh Hannover Germany + * + * (C) Copyright 2006-2010 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * reinhard.arlt@esd-electronics.de + * Based on the MPC8349EMDS config. + */ + +/* + * vme8349 board configuration file. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ + +/* Don't enable PCI2 on vme834x - it doesn't exist physically. */ +#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00100000 + +/* + * DDR Setup + */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ +#define CONFIG_SPD_EEPROM +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_SYS_READ_SPD vme8349_read_spd +#define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */ + +/* + * 32-bit data path mode. + * + * Please note that using this mode for devices with the real density of 64-bit + * effectively reduces the amount of available memory due to the effect of + * wrapping around while translating address to row/columns, for example in the + * 256MB module the upper 128MB get aliased with contents of the lower + * 128MB); normally this define should be used for devices with real 32-bit + * data path. + */ +#undef CONFIG_DDR_32BIT + +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is sys memory*/ +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ + | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) +#define CONFIG_DDR_2T_TIMING +#define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x80080001 */ + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */ + + +#define CONFIG_SYS_WINDOW1_BASE 0xf0000000 + + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */ +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */ + +#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */ + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } +/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ + +#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */ + +/* TSEC */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET) + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE +#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 +#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE +#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 +#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ + +#if defined(CONFIG_PCI) + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xFIXME + #define PCI_ENET0_MEMADDR 0xFIXME + #define PCI_IDSEL_NUMBER 0xFIXME +#endif + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + +/* + * TSEC configuration + */ + +#if defined(CONFIG_TSEC_ENET) + +#define CONFIG_GMII /* MII PHY management */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 +#define CONFIG_TSEC2_NAME "TSEC1" +#define CONFIG_PHY_M88E1111 +#define TSEC1_PHY_ADDR 0x08 +#define TSEC2_PHY_ADDR 0x10 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#ifndef CONFIG_SYS_RAMBOOT + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0xc0000) + #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + #define CONFIG_ENV_SIZE 0x2000 + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#else + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * Command line configuration. + */ +#define CONFIG_SYS_RTC_BUS_NUM 0x01 +#define CONFIG_SYS_I2C_RTC_ADDR 0x32 + +/* Pass Ethernet MAC to VxWorks */ +#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0 + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/ + +#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ + +/* System IO Config */ +#define CONFIG_SYS_SICRH 0 +#define CONFIG_SYS_SICRL SICRL_LDP_A + +#define CONFIG_SYS_GPIO1_PRELIM +#define CONFIG_SYS_GPIO1_DIR 0x00100000 +#define CONFIG_SYS_GPIO1_DAT 0x00100000 + +#define CONFIG_SYS_GPIO2_PRELIM +#define CONFIG_SYS_GPIO2_DIR 0x78900000 +#define CONFIG_SYS_GPIO2_DAT 0x70100000 + +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_HOSTNAME "VME8349" +#define CONFIG_ROOTPATH "/tftpboot/rootfs" +#define CONFIG_BOOTFILE "uImage" + +#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=vme8349\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \ + "update=protect off fff00000 fff3ffff; " \ + "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \ + "upd=run load update\0" \ + "fdtaddr=780000\0" \ + "fdtfile=vme8349.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ + "$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#ifndef __ASSEMBLY__ +int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen, + unsigned char *buffer, int len); +#endif + +#endif /* __CONFIG_H */ |