diff options
Diffstat (limited to 'include/ns16550.h')
| -rw-r--r-- | include/ns16550.h | 254 |
1 files changed, 254 insertions, 0 deletions
diff --git a/include/ns16550.h b/include/ns16550.h new file mode 100644 index 0000000..701efee --- /dev/null +++ b/include/ns16550.h @@ -0,0 +1,254 @@ +/* + * NS16550 Serial Port + * originally from linux source (arch/powerpc/boot/ns16550.h) + * + * Cleanup and unification + * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH + * + * modified slightly to + * have addresses as offsets from CONFIG_SYS_ISA_BASE + * added a few more definitions + * added prototypes for ns16550.c + * reduced no of com ports to 2 + * modifications (c) Rob Taylor, Flying Pig Systems. 2000. + * + * added support for port on 64-bit bus + * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems + */ + +/* + * Note that the following macro magic uses the fact that the compiler + * will not allocate storage for arrays of size 0 + */ + +#include <linux/types.h> + +#ifdef CONFIG_DM_SERIAL +/* + * For driver model we always use one byte per register, and sort out the + * differences in the driver + */ +#define CONFIG_SYS_NS16550_REG_SIZE (-1) +#endif + +#if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0) +#error "Please define NS16550 registers size." +#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL) +#define UART_REG(x) u32 x +#elif (CONFIG_SYS_NS16550_REG_SIZE > 0) +#define UART_REG(x) \ + unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \ + unsigned char x; +#elif (CONFIG_SYS_NS16550_REG_SIZE < 0) +#define UART_REG(x) \ + unsigned char x; \ + unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1]; +#endif + +/** + * struct ns16550_platdata - information about a NS16550 port + * + * @base: Base register address + * @reg_width: IO accesses size of registers (in bytes) + * @reg_shift: Shift size of registers (0=byte, 1=16bit, 2=32bit...) + * @clock: UART base clock speed in Hz + * @bdf: PCI slot/function (pci_dev_t) + */ +struct ns16550_platdata { + unsigned long base; + int reg_width; + int reg_shift; + int reg_offset; + int clock; + u32 fcr; +#if defined(CONFIG_PCI) && defined(CONFIG_SPL) + int bdf; +#endif +}; + +struct udevice; + +struct NS16550 { + UART_REG(rbr); /* 0 */ + UART_REG(ier); /* 1 */ + UART_REG(fcr); /* 2 */ + UART_REG(lcr); /* 3 */ + UART_REG(mcr); /* 4 */ + UART_REG(lsr); /* 5 */ + UART_REG(msr); /* 6 */ + UART_REG(spr); /* 7 */ +#ifdef CONFIG_SOC_DA8XX + UART_REG(reg8); /* 8 */ + UART_REG(reg9); /* 9 */ + UART_REG(revid1); /* A */ + UART_REG(revid2); /* B */ + UART_REG(pwr_mgmt); /* C */ + UART_REG(mdr1); /* D */ +#else + UART_REG(mdr1); /* 8 */ + UART_REG(reg9); /* 9 */ + UART_REG(regA); /* A */ + UART_REG(regB); /* B */ + UART_REG(regC); /* C */ + UART_REG(regD); /* D */ + UART_REG(regE); /* E */ + UART_REG(uasr); /* F */ + UART_REG(scr); /* 10*/ + UART_REG(ssr); /* 11*/ +#endif +#ifdef CONFIG_DM_SERIAL + struct ns16550_platdata *plat; +#endif +}; + +#define thr rbr +#define iir fcr +#define dll rbr +#define dlm ier + +typedef struct NS16550 *NS16550_t; + +/* + * These are the definitions for the FIFO Control Register + */ +#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */ +#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ +#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ +#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ +#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ +#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ +#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ +#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ +#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ + +#define UART_FCR_RXSR 0x02 /* Receiver soft reset */ +#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */ + +/* Ingenic JZ47xx specific UART-enable bit. */ +#define UART_FCR_UME 0x10 + +/* Clear & enable FIFOs */ +#define UART_FCR_DEFVAL (UART_FCR_FIFO_EN | \ + UART_FCR_RXSR | \ + UART_FCR_TXSR) + +/* + * These are the definitions for the Modem Control Register + */ +#define UART_MCR_DTR 0x01 /* DTR */ +#define UART_MCR_RTS 0x02 /* RTS */ +#define UART_MCR_OUT1 0x04 /* Out 1 */ +#define UART_MCR_OUT2 0x08 /* Out 2 */ +#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ +#define UART_MCR_AFE 0x20 /* Enable auto-RTS/CTS */ + +#define UART_MCR_DMA_EN 0x04 +#define UART_MCR_TX_DFR 0x08 + +/* + * These are the definitions for the Line Control Register + * + * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting + * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. + */ +#define UART_LCR_WLS_MSK 0x03 /* character length select mask */ +#define UART_LCR_WLS_5 0x00 /* 5 bit character length */ +#define UART_LCR_WLS_6 0x01 /* 6 bit character length */ +#define UART_LCR_WLS_7 0x02 /* 7 bit character length */ +#define UART_LCR_WLS_8 0x03 /* 8 bit character length */ +#define UART_LCR_STB 0x04 /* # stop Bits, off=1, on=1.5 or 2) */ +#define UART_LCR_PEN 0x08 /* Parity eneble */ +#define UART_LCR_EPS 0x10 /* Even Parity Select */ +#define UART_LCR_STKP 0x20 /* Stick Parity */ +#define UART_LCR_SBRK 0x40 /* Set Break */ +#define UART_LCR_BKSE 0x80 /* Bank select enable */ +#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ + +/* + * These are the definitions for the Line Status Register + */ +#define UART_LSR_DR 0x01 /* Data ready */ +#define UART_LSR_OE 0x02 /* Overrun */ +#define UART_LSR_PE 0x04 /* Parity error */ +#define UART_LSR_FE 0x08 /* Framing error */ +#define UART_LSR_BI 0x10 /* Break */ +#define UART_LSR_THRE 0x20 /* Xmit holding register empty */ +#define UART_LSR_TEMT 0x40 /* Xmitter empty */ +#define UART_LSR_ERR 0x80 /* Error */ + +#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ +#define UART_MSR_RI 0x40 /* Ring Indicator */ +#define UART_MSR_DSR 0x20 /* Data Set Ready */ +#define UART_MSR_CTS 0x10 /* Clear to Send */ +#define UART_MSR_DDCD 0x08 /* Delta DCD */ +#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ +#define UART_MSR_DDSR 0x02 /* Delta DSR */ +#define UART_MSR_DCTS 0x01 /* Delta CTS */ + +/* + * These are the definitions for the Interrupt Identification Register + */ +#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ +#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ + +#define UART_IIR_MSI 0x00 /* Modem status interrupt */ +#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ +#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ +#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ + +/* + * These are the definitions for the Interrupt Enable Register + */ +#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ +#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ +#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ +#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ + +/* useful defaults for LCR */ +#define UART_LCR_8N1 0x03 + +void NS16550_init(NS16550_t com_port, int baud_divisor); +void NS16550_putc(NS16550_t com_port, char c); +char NS16550_getc(NS16550_t com_port); +int NS16550_tstc(NS16550_t com_port); +void NS16550_reinit(NS16550_t com_port, int baud_divisor); + +/** + * ns16550_calc_divisor() - calculate the divisor given clock and baud rate + * + * Given the UART input clock and required baudrate, calculate the divisor + * that should be used. + * + * @port: UART port + * @clock: UART input clock speed in Hz + * @baudrate: Required baud rate + * @return baud rate divisor that should be used + */ +int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate); + +/** + * ns16550_serial_ofdata_to_platdata() - convert DT to platform data + * + * Decode a device tree node for an ns16550 device. This includes the + * register base address and register shift properties. The caller must set + * up the clock frequency. + * + * @dev: dev to decode platform data for + * @return: 0 if OK, -EINVAL on error + */ +int ns16550_serial_ofdata_to_platdata(struct udevice *dev); + +/** + * ns16550_serial_probe() - probe a serial port + * + * This sets up the serial port ready for use, except for the baud rate + * @return 0, or -ve on error + */ +int ns16550_serial_probe(struct udevice *dev); + +/** + * struct ns16550_serial_ops - ns16550 serial operations + * + * These should be used by the client driver for the driver's 'ops' member + */ +extern const struct dm_serial_ops ns16550_serial_ops; |